Видео

Thanks for the compliments. The pdf slides are attached in the video in the form of link in the description section of the video. Alternatively, you may send email to jalaghari1@gmail.com, they will be shared with you.

JazakALLAH

Thanks for the comment. The pdf of all lectures are attached in the form of link in the description section of the video, you may download it from there. Alternatively, you may send the email to jalaghari1@gmail.com, it will be shared with you.

Thanks for the compliments.

Thanks for the comment. It depends upon the model you are using. In this model, I thik step input is 1.

Thanks for the compliments. For the optimization of multiple PID controllers, you may kindly watch the video PSO based automatic generation control in which I have optimized three pid controllers.

@@DrJALAGHARI Thank you very much!

Thanks for the comment. The initial voltage for the slack bus is 1.05pu.

You are welcome.

Thanks for the comment. Kindly watch the video step by step for better understanding.

Thanks for the compliments and query. I think better to put the 2 series and parallel to 1 and measure yor results. if the results are correct then ok otherwise change it.

Wa'alaikum Salam Thanks for your concern. I will add new videos very soon on this channel within few days. you may suggest any topic of your interest too.

Thanks for the compliments. Do share this video as well as channel with your friends too.

Thanks for the comment. May I know which Matlab version you are using? Sometime due to matlab version, it may give error.

@DrJALAGHARI it could be true. It was on matlab 2103. I deleted and installed 2024 and it worked fine and I solved it. Thank you

THanks for the comment. ITAE mean Integral Time Absolute Error. for details, you may kindly follow the research paper which I have shared in the video.

THanks for the comment. You can apply the grey wolf optimization code in simulink by following my video on PSO based load freqeuncy control in simulink.

Thanks for the comment. Kindly send email to jalaghari1@gmail.com, it will be shared with you.

Thanks for the positive feedback. Sure.

Thanks for the compliments. Do share this video and channel within your circle.

Thanks for the comment. It is used randomly.

Wa'alaikum Salam

@@quangvinh4701 Thanks for the comment and suggestions. Sure.

Thanks for the comment. You can connect the scope at the output of P port to get the receiving end active power.

Thanks for the compliments. You may watch my other videos, I have tested it on different controllers. You may also take the same system and apply new controller.

Thanks for the comment. Sure.

Thanks for the comment. May I know the reason why it is not opening? or you may send email to jalaghari1@gmail.com, it will be sent to you.

Thanks for the comment. you must have the values.

Thank you so much for the compliments.

Thanks for the comment. You may go through feedback control system theory for this justification.

Wa'alaikum salam, Thanks for the comment. To know the best value for P, I, and D, we have used kk as vairable in the block. genetic algorithm will change the different values to get the best results. once, the simulation is completed, you may see the value of kk in the workspace section. double click on the kk variable, it will show three values, one for P, other for I and last for D.

Thanks for the compliments.

Thanks for the feedback. You may kinly watch my tutorials on different topics of electrical engineering. I am sure you will like those tutorials.

Thanks for the comment. Kindly watch my videos like genetic algorithm and PSO based load frequency control or automatic generation control for better understanding of PID values.

Wa'alaikum salam, thanks for the comment. You may check again to set the Gen2 and3 to PV bus.

Thanks for subscribing this channel.

Thanks for the comment. No.

Thanks for the compliments.

Hello Sir! If i want to get graphs for all faults, how i will add scopes here? and codes??

Thanks for the compliments.

Thanks for the comment. You may add the graph at the three measurement block.

Thanks for the comment. Which file?

@@DrJALAGHARI sorry sir you're pdf is executed successfully sorry for you're inconvenience

Thanks for the comment. You may have to apply ANN separately for each area as well as Tie line.

Thanks for the compliments. You may apply the same idea for both the two area power systems. Also, watch my other videos on this topic, they will be helpful to you.

Thanks foe the comment. I use MATLAB version 2017a.

Thanks for the comment. I use MATLAB version 2017a.

Thanks for the comment. Kindly watch the video step by step for better understanding.

Thanks for the comment. for this purpose, you have to download and save hadi sadat folder in MATLAB.

Thanks

Thanks for the comment. You may go through a research paper on this topic for better understanidng.